Pro-433 user manual

If you use a cigarette-lighter adapter, you might hear some NOTE electrical interference from your engine while scanning. Page 7 You also may need a BNC adapter not supplied. PGM appears in the display. Page 9 Quick Start. Select the target bank. Press to access the target channel. A channel is a programmable memory location for storing frequencies that you can scan for activity. Channels are grouped into 10 channel- storage banks, each of which contains channels.

PC interface cable connection. Selects the ham band when in service mode. Selects the marine band when in service mode. Selects the air band when in service mode. Selects the police band when in service mode. Page 14 The Basics DATA Appears when the data skip function is active, and in the trunking mode when the dis connect tone detect function is off. Appears when Signal Stalker I is active. SCAN Appears during channel scan. LIST Appears with numbers 1—5 during trunking.

A bar indicates which ID scan list banks are turned on for scanning. Page Replacing The Fuse The Basics Indicates the search direction during a chain, direct, or service search, and normal and weather scan. Page Beyond The Basics Beyond the Basics beyond the basics channel-storage banks The scanner displays the channel-storage bank number while scanning a channel. To increase scanning speed, you can lock out channels with continuous transmission, such as weather channels or birdies.

Page Chain Search Beyond the Basics chain search Chain search lets you search through preset frequency ranges and store found frequencies. You can also modify each range. At least one bank must be active. If you disable all the NOTE banks, the error tone beeps. Press to change to the upper limit frequency. Warning L Watch L Advisory WXA Page Skywarn Beyond the Basics Skywarn Skywarn jumps directly to the last channel in memory from any mode.

The scanner pauses any active scans and starts receiving transmissions in the last channel. If no frequency is programmed in the last channel, No Prog appears and the scanner sounds an error tone. Alert settings S-S. Back light settings S-S. Pager screen settings S-S. OnlY setting to ON. Page Keytones Beyond the Basics. Press MENU to exit the menu mode.

To modify keytone settings, complete the following steps:. Press MENU. For trunked reception, set the squelch at the center position. Storing talk group IDs. Select the trunking programming mode and the bank you want to change. Use the supplied mounting bracket as a template to mark positions for the two mounting screws. At the marked positions, drill holes slightly smaller than the screws. When drilling holes, be sure to avoid obstructions and wires behind the mounting surface.

Attach the mounting bracket to the surface using the supplied screws. Remove the four rear screws that secure the outer metal case and pull off the case with care. Insert the DIN sleeve into the opening in your dashboard, lip facing out. Slowly slide the scanner into the sleeve until it locks in place. If you use a cigarette-lighter adapter, you might hear some NOTE electrical interference from your engine while scanning. The grounding screw must make complete contact with the metal frame of your vehicle.

NOTES you use your scanner as a base station. If you mount your scanner. Always use ohm coaxial cable, such as RG or RG-8, to connect an outdoor antenna. For lengths over 50 feet, use RG-8 low-loss dielectric coaxial cable.

You also may need a BNC adapter not supplied. If the antenna starts to fall, let it go! If the antenna touches a power line, touching the antenna, mast, cable, or guy wires can cause electrocution and death. Call the. PGM appears in the display. The scanner automatically rounds the entered number to the nearest valid frequency. For example, If you entered a frequency that is already saved on NOTE another channel, the scanner beeps and displays the. Select the target bank.

The smallest empty channel number. T o cancel the copy or move, press. Press and hold SRCH. SRCH appears in the display. Press or to begin searching up or down the frequencies. Extended highvolume listening can lead to permanent hearing loss. Over time, your ears adapt to the volume level, so a volume level that does not cause discomfort might still damage your hearing.

A frequency is the tuning location of a station. A channel is a programmable memory location for storing frequencies that you can scan for activity. Channels are grouped into 10 channel-. For example, many amateur radio frequencies are located in the HAM service bank. Doing so could subject you to legal penalties. It is legal to listen to almost every transmission your scanner can receive. However, there are some transmissions you should never intentionally listen to.

These include:. Starts and stops channel scans, or lets you directly enter a frequency or channel number. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions.